10–12 March 2027 · BITEC

Intelligent Asia Thailand & GRTE 2027 Stand Construction | Bangkok

Two very different technical communities share the same week at BITEC. Electronics line builders want a clean, static-controlled look around precision kit, while rubber and tyre exhibitors bring presses and mixers that weigh far more than any display fixture.

Quote for this show

Tell us the stand size and equipment. Drawings can follow by email.

01Show facts
Dates
10–12 March 2027
Venue
Bangkok International Trade & Exhibition Centre (BITEC), 88 Bangna-Trad Road (Km.1), Bangna, Bangkok 10260
Halls
Intelligent Asia Thailand: Event Hall 99 per the organiser's site. GRTE is listed in Hall 100 by exhibitors; confirm both in the manual.
Organiser
Chan Chao International Co., Ltd (Intelligent Asia Thailand); TechnoBiz (GRTE, the Global Rubber, Latex & Tyre Expo)
Exhibitor profile
PCB manufacturing and industrial automation suppliers, plus rubber, latex and tyre machinery and materials exhibitors.
02Technical build requirements

What the structure has to carry at Intelligent Asia Thailand & GRTE

Two audiences, two structural briefs

PCB and automation stands are mostly about steady benches, power quality and tidy cable runs. Rubber and tyre stands are about machine mass and move-in logistics. We scope the two differently, even for one client with a foot in both.

Press and mixer footprint loading

Rubber processing equipment can be heavy on a small footprint. Permitted floor loading in the hall must come from the organiser; confirm with organiser — we handle this for you, then we size plates against your data sheet.

Confirm with organiser — we handle this for you

Clean, level benches for electronics

Inspection and placement machines are sensitive to vibration and levelling. We build rigid, shimmed benches and keep foot traffic routes clear of the stand edge nearest the equipment.

Power distribution and earthing

Automation demos often need several circuits at once. Supply capacity is ordered through the organiser by amperage; confirm with organiser — we handle this for you, and we prepare stand-side distribution before the machines land.

Confirm with organiser — we handle this for you

Rigging and double-deck approval

Hanging signs need venue-approved rigging, and any raised meeting level needs a stamped structural pack. Hall height and rigging limits: confirm with organiser — we handle this for you.

Confirm with organiser — we handle this for you

03Typical stand sizes and budget bands

Inline

18 sqm

Single demo bench and one power drop

Essential
THB 126,000 – 162,000
USD 3,880 – 4,980
Standard
THB 180,000 – 252,000
USD 5,540 – 7,750
Premium
THB 288,000 – 432,000
USD 8,860 – 13,290

Corner

36 sqm

Level-controlled equipment area with demo wall

Essential
THB 252,000 – 324,000
USD 7,750 – 9,970
Standard
THB 360,000 – 504,000
USD 11,080 – 15,510
Premium
THB 576,000 – 864,000
USD 17,720 – 26,580

Island

54 sqm

Machine zone and meeting pod, with plated floor quoted separately

Essential
THB 378,000 – 486,000
USD 11,630 – 14,950
Standard
THB 540,000 – 756,000
USD 16,620 – 23,260
Premium
THB 864,000 – 1,296,000
USD 26,580 – 39,880

Planning ranges per sqm: Essential THB 7,000–9,000 · Standard THB 10,000–14,000 · Premium THB 16,000–24,000. USD at THB 32.5 = USD 1. Double-deck structures, machinery platforms and rigging are quoted on top of these ranges. Pixelmate Exhibition Co., Ltd. confirms the figure after reviewing your drawings.

04What Pixelmate built here

No published project photograph from these two shows yet. Our approach to precision kit is to isolate the equipment zone structurally so a busy aisle does not move the bench.

Pixelmate show guides on pixelmateexpo.com
05Technical FAQ
Do machines on a bench need special floor treatment?

A rigid, levelled base matters more than the floor covering. We build the bench frame on adjustable feet and check it with a spirit level before the equipment is lifted on.

Can one stand serve both PCB and rubber customers?

Yes, by zoning. The static-sensitive display sits away from the aisle edge, and heavier equipment sits on plated areas close to the delivery side.

How early should drawings reach the organiser?

Exhibitor-manual deadlines apply to raised structures and rigging. We work back from those dates, so confirm the dates with the organiser as soon as the stand is confirmed.

What equipment data do you need from us?

Weight, footprint, number of support feet, power rating and any compressed air or cooling need. That sheet drives both the deck design and the electrical order.

Can LED walls hang from the stand structure?

They can when the frame is designed for the load. We confirm the panel weight and fixing method in the drawings and submit them if the organiser asks.

Send your drawings for Intelligent Asia Thailand & GRTE

Pixelmate Exhibition Co., Ltd. reviews the equipment, hall and approval route, then returns a technical estimate.

Upload drawings

Cookies

We use essential storage to run this site and, with your consent, anonymous analytics to improve it. Your enquiry details are only used to respond to your project.